diff options
Diffstat (limited to 'doc/classes/VehicleWheel3D.xml')
| -rw-r--r-- | doc/classes/VehicleWheel3D.xml | 8 |
1 files changed, 3 insertions, 5 deletions
diff --git a/doc/classes/VehicleWheel3D.xml b/doc/classes/VehicleWheel3D.xml index 35f1189a06..951f4f8275 100644 --- a/doc/classes/VehicleWheel3D.xml +++ b/doc/classes/VehicleWheel3D.xml @@ -32,7 +32,7 @@ </methods> <members> <member name="brake" type="float" setter="set_brake" getter="get_brake" default="0.0"> - Slows down the wheel by applying a braking force. The wheel is only slowed down if it is in contact with a surface. The force you need to apply to adequately slow down your vehicle depends on the [member RigidBody3D.mass] of the vehicle. For a vehicle with a mass set to 1000, try a value in the 25 - 30 range for hard braking. + Slows down the wheel by applying a braking force. The wheel is only slowed down if it is in contact with a surface. The force you need to apply to adequately slow down your vehicle depends on the [member RigidDynamicBody3D.mass] of the vehicle. For a vehicle with a mass set to 1000, try a value in the 25 - 30 range for hard braking. </member> <member name="damping_compression" type="float" setter="set_damping_compression" getter="get_damping_compression" default="0.83"> The damping applied to the spring when the spring is being compressed. This value should be between 0.0 (no damping) and 1.0. A value of 0.0 means the car will keep bouncing as the spring keeps its energy. A good value for this is around 0.3 for a normal car, 0.5 for a race car. @@ -41,7 +41,7 @@ The damping applied to the spring when relaxing. This value should be between 0.0 (no damping) and 1.0. This value should always be slightly higher than the [member damping_compression] property. For a [member damping_compression] value of 0.3, try a relaxation value of 0.5. </member> <member name="engine_force" type="float" setter="set_engine_force" getter="get_engine_force" default="0.0"> - Accelerates the wheel by applying an engine force. The wheel is only speed up if it is in contact with a surface. The [member RigidBody3D.mass] of the vehicle has an effect on the acceleration of the vehicle. For a vehicle with a mass set to 1000, try a value in the 25 - 50 range for acceleration. + Accelerates the wheel by applying an engine force. The wheel is only speed up if it is in contact with a surface. The [member RigidDynamicBody3D.mass] of the vehicle has an effect on the acceleration of the vehicle. For a vehicle with a mass set to 1000, try a value in the 25 - 50 range for acceleration. [b]Note:[/b] The simulation does not take the effect of gears into account, you will need to add logic for this if you wish to simulate gears. A negative value will result in the wheel reversing. </member> @@ -49,7 +49,7 @@ The steering angle for the wheel. Setting this to a non-zero value will result in the vehicle turning when it's moving. </member> <member name="suspension_max_force" type="float" setter="set_suspension_max_force" getter="get_suspension_max_force" default="6000.0"> - The maximum force the spring can resist. This value should be higher than a quarter of the [member RigidBody3D.mass] of the [VehicleBody3D] or the spring will not carry the weight of the vehicle. Good results are often obtained by a value that is about 3× to 4× this number. + The maximum force the spring can resist. This value should be higher than a quarter of the [member RigidDynamicBody3D.mass] of the [VehicleBody3D] or the spring will not carry the weight of the vehicle. Good results are often obtained by a value that is about 3× to 4× this number. </member> <member name="suspension_stiffness" type="float" setter="set_suspension_stiffness" getter="get_suspension_stiffness" default="5.88"> This value defines the stiffness of the suspension. Use a value lower than 50 for an off-road car, a value between 50 and 100 for a race car and try something around 200 for something like a Formula 1 car. @@ -77,6 +77,4 @@ This value affects the roll of your vehicle. If set to 1.0 for all wheels, your vehicle will be prone to rolling over, while a value of 0.0 will resist body roll. </member> </members> - <constants> - </constants> </class> |