diff options
Diffstat (limited to 'doc/classes/PhysicsServer.xml')
| -rw-r--r-- | doc/classes/PhysicsServer.xml | 28 |
1 files changed, 13 insertions, 15 deletions
diff --git a/doc/classes/PhysicsServer.xml b/doc/classes/PhysicsServer.xml index 88a104cb11..7dfc8e66d4 100644 --- a/doc/classes/PhysicsServer.xml +++ b/doc/classes/PhysicsServer.xml @@ -1260,7 +1260,7 @@ The higher, the stronger. </constant> <constant name="PIN_JOINT_IMPULSE_CLAMP" value="2" enum="PinJointParam"> - If above 0, this value is the maximum value for an impulse that this Joint puts on it's ends. + If above 0, this value is the maximum value for an impulse that this Joint puts on its ends. </constant> <constant name="HINGE_JOINT_BIAS" value="0" enum="HingeJointParam"> The speed with which the two bodies get pulled together when they move in different directions. @@ -1401,31 +1401,31 @@ <constant name="G6DOF_JOINT_LINEAR_MOTOR_FORCE_LIMIT" value="6" enum="G6DOFJointAxisParam"> The maximum force that the linear motor can apply while trying to reach the target velocity. </constant> - <constant name="G6DOF_JOINT_ANGULAR_LOWER_LIMIT" value="7" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_LOWER_LIMIT" value="10" enum="G6DOFJointAxisParam"> The minimum rotation in negative direction to break loose and rotate around the axes. </constant> - <constant name="G6DOF_JOINT_ANGULAR_UPPER_LIMIT" value="8" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_UPPER_LIMIT" value="11" enum="G6DOFJointAxisParam"> The minimum rotation in positive direction to break loose and rotate around the axes. </constant> - <constant name="G6DOF_JOINT_ANGULAR_LIMIT_SOFTNESS" value="9" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_LIMIT_SOFTNESS" value="12" enum="G6DOFJointAxisParam"> A factor that gets multiplied onto all rotations across the axes. </constant> - <constant name="G6DOF_JOINT_ANGULAR_DAMPING" value="10" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_DAMPING" value="13" enum="G6DOFJointAxisParam"> The amount of rotational damping across the axes. The lower, the more dampening occurs. </constant> - <constant name="G6DOF_JOINT_ANGULAR_RESTITUTION" value="11" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_RESTITUTION" value="14" enum="G6DOFJointAxisParam"> The amount of rotational restitution across the axes. The lower, the more restitution occurs. </constant> - <constant name="G6DOF_JOINT_ANGULAR_FORCE_LIMIT" value="12" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_FORCE_LIMIT" value="15" enum="G6DOFJointAxisParam"> The maximum amount of force that can occur, when rotating around the axes. </constant> - <constant name="G6DOF_JOINT_ANGULAR_ERP" value="13" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_ERP" value="16" enum="G6DOFJointAxisParam"> When correcting the crossing of limits in rotation across the axes, this error tolerance factor defines how much the correction gets slowed down. The lower, the slower. </constant> - <constant name="G6DOF_JOINT_ANGULAR_MOTOR_TARGET_VELOCITY" value="14" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_MOTOR_TARGET_VELOCITY" value="17" enum="G6DOFJointAxisParam"> Target speed for the motor at the axes. </constant> - <constant name="G6DOF_JOINT_ANGULAR_MOTOR_FORCE_LIMIT" value="15" enum="G6DOFJointAxisParam"> + <constant name="G6DOF_JOINT_ANGULAR_MOTOR_FORCE_LIMIT" value="18" enum="G6DOFJointAxisParam"> Maximum acceleration for the motor at the axes. </constant> <constant name="G6DOF_JOINT_FLAG_ENABLE_LINEAR_LIMIT" value="0" enum="G6DOFJointAxisFlag"> @@ -1434,10 +1434,10 @@ <constant name="G6DOF_JOINT_FLAG_ENABLE_ANGULAR_LIMIT" value="1" enum="G6DOFJointAxisFlag"> If [code]set[/code] there is rotational motion possible. </constant> - <constant name="G6DOF_JOINT_FLAG_ENABLE_MOTOR" value="2" enum="G6DOFJointAxisFlag"> + <constant name="G6DOF_JOINT_FLAG_ENABLE_MOTOR" value="4" enum="G6DOFJointAxisFlag"> If [code]set[/code] there is a rotational motor across these axes. </constant> - <constant name="G6DOF_JOINT_FLAG_ENABLE_LINEAR_MOTOR" value="3" enum="G6DOFJointAxisFlag"> + <constant name="G6DOF_JOINT_FLAG_ENABLE_LINEAR_MOTOR" value="5" enum="G6DOFJointAxisFlag"> If [code]set[/code] there is a linear motor on this axis that targets a specific velocity. </constant> <constant name="SHAPE_PLANE" value="0" enum="ShapeType"> @@ -1518,9 +1518,7 @@ <constant name="BODY_MODE_RIGID" value="2" enum="BodyMode"> Constant for rigid bodies. </constant> - <constant name="BODY_MODE_SOFT" value="3" enum="BodyMode"> - </constant> - <constant name="BODY_MODE_CHARACTER" value="4" enum="BodyMode"> + <constant name="BODY_MODE_CHARACTER" value="3" enum="BodyMode"> Constant for rigid bodies in character mode. In this mode, a body can not rotate, and only its linear velocity is affected by physics. </constant> <constant name="BODY_PARAM_BOUNCE" value="0" enum="BodyParameter"> |